Essential checks for keeping utility crews safe in remote work
@workingalonewatch
Why a remote work safety checklist matters for contractors and utility crews
Working away from the office brings a different set of hazards. For contractors and utility crews, the job often takes them to isolated sites, rough terrain, or areas with no mobile reception. A minor injury or sudden health issue can turn serious fast when help is far away. That is why having a remote worker safety device and a clear plan for using it is not optional - it is a core part of the job.
This article walks through a practical checklist for anyone who supervises or works as part of a remote utility crew. The goal is to help you think through the gear, the communication setup, and the daily habits that keep people safer when they work alone or in small teams far from support. The points here are drawn from common industry practice and from the kind of thinking that goes into products like the Mercari Lone Worker Alarm NZ, which is designed for this exact environment.
Check the device itself before every shift
A remote worker safety device only helps if it is fully charged, working correctly, and worn properly. Before anyone heads out, make these checks part of the routine.
- Battery and power status. Confirm the device has enough charge for the full shift. If it uses replaceable batteries, carry spares. A device that dies halfway through the day is no help at all.
- Signal and connectivity. Check that the device can connect to the network it relies on - cellular, satellite, or a dedicated radio system. In areas with patchy coverage, test the connection at the site before the crew disperses.
- Wear and attachment. Make sure the device is secured on the body where it will not snag or fall off. Belt clips, lanyards, and hard-hat mounts should be inspected for damage. A device that drops and breaks is a loss, but one that is not worn at all is worse.
- Fall detection and man-down features. If the device has automatic alerts for a fall or lack of movement, test that the sensor is enabled and calibrated. Some devices let you choose sensitivity levels - set them for the type of work being done.
- Two-way voice and SOS button. Verify that the emergency button is not blocked or pressed accidentally by gear. Test the voice channel if the device includes one. The crew should know how to initiate a call and what happens after they press it.
Once these checks are done, the device can be trusted. But trust is only as good as the habits that support it.

Plan the communication chain before the work starts
Having a loneworkeralarms.co.nz device on every crew member is a solid start, but the system only works if someone is actually monitoring the alerts. Decide ahead of time who will receive the notifications and what they will do when one comes in. This could be a dedicated safety officer in a control room, a supervisor on site, or a family contact. The important thing is that the person on the other end knows the location of each worker and has a plan for each type of alert.
For utility crews, the work often involves climbing poles, entering manholes, or operating heavy equipment. These tasks make it hard to press a button in an emergency. An automatic man-down alert that triggers when the device detects a sudden impact or no movement for a set time is a real advantage. The crew should understand how long the delay is before the alert goes out, and they should know that the device can be cancelled if they are simply resting or working in a static position.
Train the crew on what to do when an alert happens
A device is only as effective as the person wearing it. Every contractor and utility worker should go through a short briefing on the remote worker safety device they will carry. Cover these points:
- How to start and end a shift on the device. Some devices need a check-in at the start of the day and a sign-off at the end. Missing the sign-off can trigger a false alarm, so everyone needs to know the procedure.
- What the SOS button does. Pressing it should be reserved for genuine emergencies. A false alarm wastes response time and can cause panic. But workers should never hesitate to use it if they are in danger.
- How to cancel an accidental alert. If the device triggers a fall alert by mistake, the worker needs to know how to cancel it within the grace period. This keeps the system honest and avoids unnecessary call-outs.
- What happens after the alert is sent. Will the monitoring service call the worker first? Will emergency services be dispatched directly? The crew should know the sequence so they can act accordingly.
Training should be repeated whenever a new device is introduced or when the crew rotates. A quick five-minute refresher at the start of a new project can prevent confusion later.
Consider the environment and the work itself
Remote work safety is not just about the device. The surroundings and the tasks change the risk profile. For utility crews, factors like weather, terrain, and the presence of high-voltage lines or gas mains all affect how a safety plan should be set up.
If the crew works in extreme heat or cold, the device battery may drain faster. Keep spare batteries in an insulated pouch. If the work involves water or mud, check that the device is water-resistant or waterproof to the right standard. A device that fails because it got wet is a liability.

When working near live electrical equipment, make sure the device itself does not create a hazard. Some lone worker alarms are designed to be worn over clothing and do not conduct electricity, but it is worth verifying the specifications. The same goes for working near gas - the device should not be a source of ignition in a potentially flammable atmosphere.
Make the device part of the daily routine
The best safety equipment is the one that gets used. A remote worker safety device that sits in a truck cab or in a locker does nothing. Encourage the crew to treat the device like their hard hat or safety vest - something they put on before they start and keep on until they finish.
Supervisors should model the behaviour. If the boss wears the device, the crew is more likely to wear theirs. It also helps to build a culture where checking the device is as normal as checking the tyres on the work truck.
For teams that work across multiple sites, having a centralised system that tracks who is where and what their device status is can be a huge help. This is where a platform like loneworkeralarms.co.nz comes in - it gives visibility across the whole operation without needing a dedicated dispatcher at every location. The Mercari Lone Worker Alarm NZ is one example of a device that feeds into such a system, providing GPS location, fall detection, and two-way voice communication without tying the crew to a mandatory monitoring contract.
Review and update the checklist regularly
No checklist is perfect forever. As new devices come on the market, as the crew changes, or as the work environment shifts, the safety plan should be reviewed. Set a reminder to go through the checklist every quarter. Ask the crew if they have any issues with the current device or process. Sometimes the best improvements come from the people who use the gear every day.

When a new remote worker safety device is introduced, run through the full checklist again. Even if the new device looks similar, the buttons, alerts, and battery life may be different. A quick re-training session can prevent confusion and keep everyone safe.
Safety in remote work is not complicated, but it does require consistency. The device is a tool, not a solution by itself. The real safety comes from the habits, the training, and the willingness to check and double-check before every shift. For contractors and utility crews, that combination is what makes the difference between a good day and a bad one.
Mercari Lone Worker Alarm NZ on social media
YouTube